Search results

Faulty volt/ohm meter….,…ouch😂😂😂

Not sure how the pre-wired setup works off of your tow vehicle or your house battery.. I installed my camera by tapping into the rigs running lights which are powered by my truck when the lights are on. I know that you could get voltage drop by the length of you conductors (wires) and the...

I’m sorry but I don’t remember. You should be able to check with a volt/ohm meter.

Attached is Lippert's recommendations.

Not sure what type of system you have in the 2021. I have a 2013 Cyclone 3010 that has a hydraulic pump and two solenoids and I have had to manually operate them. One of the solenoids is for the slideouts and one for the landing gear. The pump and slideout solenoid are located near each other...

I had the same experience. It started over a year period. While on a recent road trip with a one night stop in Lubbock, TX my landing gear failed to come up after I pulled the slideouts in. I had to manually raise them. Stopped at an RV store and picked up a new battery and installed it at our...

This is not good. I have stink in mine as well. I’m planning on replacing my EPDM roof system soon and will check the vent pipes at that time. Thanks for sharing the pics of the problem!

I installed a Furrion system with a rear camera and two sides last April. Connected it to the 3010’s running lights. You need to check what wires are positive and negative as the two sides had all white wires. The rear had a green and a white. The trailer needs to be plugged in to the towing...

The upholstry is peeling on my sofa/couch which I am seeing is a common issue. I like the storage that we have with this setup and I am not looking to replace with something different. The plan is to re-upholster using Sunbrella material. My question is: Has any of you that has a Cyclone 3010 or...

I have a 2013 Cyclone 3010 that’s similar to the Warrior. A heads up on the switching valve operation if the operation was not explained to you. If you are on “City” do not rotate the valve switch to “Tank” or “Normal” while you have water pressure on the valve. Doing so may cause damage to the...

My kitchen gray tank valve (cable actuated) stopped closing completely while I was on a five week road trip. When I got home I dropped the coroplast (what a pain that is) and removed the valve. I spent a bit of time cleaning it with simple green and blowing air into it. A lot of sand/grit kept...

I recently watched a YouTube video that found the culprit of the smell you are describing. It can be found by doing a search for “WindersRanger” and “RV Tank Vent.” The guy discovered that the Heartland factory did not run the vent pipe up through the roof. Not saying that is your issue, but...

Thank you all for your wisdom and input! It was very helpful, and based on your input I have decided not to purchase the stabilizer and supports. Hope you has a wonderful Christmas and wishing you a Happy New Year!

Hi all! i’m looking for advice/wisdom. I’m thinking of purchasing a king pin stabilizer and a pair of slideout supports. I have a few questions: 1) For those that are using or have used a king pin stabilizer, does it perform as intended, does it underperform, or is a king pin stabilizer...

Thank you to all of you for your responses! I tried to duplicate the setup that that I had at Camp Richardson at home and have not had any leaks. As per most of your responses I’m attributing the leaks to high water pressure at the Camp Richardson site. And, per recommendation I’ll be looking...

Hey guys, made a trip to South Lake Tahoe and stayed at Camp Richardson with full hookups. I developed a leak in the pex plumbing at the fittings behind the Anderson Kantleak 4-way valve. My first inclination before pulling the bulkhead in the basement was my hot water heater was leaking only to...

jesstalkn and LBR thank you so much for your input. It’s given me a great deal of comfort knowing there are no issues and what I was seeing was normal. I’ll have to drop the coroplast sometime in the future to get a visual, maybe install some plumbing with valves��. Again, thank...

jesstalkn and LBR so the water I saw pouring out on the door side by the step is the indicator that the tanks are venting and are full? Just wanting to reaffirm and to not worry that I caused damage to one of the tanks. Do you guys have any idea what the port is on the Anderson 4-way valve is...

I bought the rig used back in September. I have been using the water capacity gauge on the control panel inside (see photo of lit panel) as an indicator to when the tank is full. On my previous TH the water would spill at the point where I filled my tank as an indicator that the tank was full...

Thanks for the heads up!! - - - Updated - - - Thanks for the heads up!! - - - Updated - - - Thanks for the heads up!! - - - Updated - - - btw, you have some good mods going on! - - - Updated - - - Thanks for the heads up. I'll check to see if the radio is connected to something. I...

I recently bought a 2013 Cyclone 3010. There’s a fitting which I’m thinking is for the radio antenna. Can anyone confirm this or tell me what it is for. Thank you in advance for any helpful information!

Thanks for the quick reply and information!!

Hi all! I’m new to the site. Recently purchased a 2013 Cyclone 3010. Can anyone tell me what the toggle switch in the docking station is for. I thought it was for the water pump, but the pump works regardless of the switch position. Thanks in advance for your help😊