Re: Not sure why the negative looks like this
A possibility? Negative cable installed last,correct way to do it, an arc occurred possibly charger on,short,or load? Doesn't look like corrosion relatively new battery.
If you have a heat register in floor in line with rear axle try removing it to see if you can access sensor. I can in ours but have no idea how yours is.
Lockpick for 16 and older
https://www.coastaletech.com/mytouch.htm
I have the camera and TPMS system for 17 and later. It works good lacks some features that would make it better. Can not look at while driving is one
The popping noise and settling could be 2 different issues. Mine was settling on left side after checking hoses and jacks I checked the solenoids on the valves by using an allen wrench and making sure adjustment was all the way out(CCW). I found 1 on front jack that I got about 1/4 turn. Seams...
Re: Considering 2018 F450 Lariat Ultimate
The C&C are derated the pickup is not. The tpms sensors work on my G114,but the valve stems supplied by Ford will not.Need .625 stems.
I replaced 1 on mine. Been awhile, cable was about $30 on Amazon B.A.L. is slide manufacture I believe.Not a hard job cutting cable without fraying ends was only problem.
I have done this. On the remote for the Progressive there is a switch that will eliminate the code on the display.Not sure how it works if just eliminating that function or jumping neut and ground.
positive to positive and negative to negative, parallel connected, take load from positive of first battery and negative of last voltage stays the same amp hours add
Duane
You could be right.I was thinking bags for leveling would not be needed but using them to help cushion suspension might help.Or give Kelderman a call.In looking at helpers after trip can see where they were hitting pads but no wear on them.
First tow with 17/ 450 2400 miles now
Trailer 17100# 3500# pin Mor/ryde IS 17.5 tires
Truck is 13100# with trailer
Trailer caused truck to set down 3 1/4" truck and trailer both level,checked with 4' level on level cement pad,no air bags,with trailer truck just starting to touch helper springs...
The dealer told me there were 3 different length extensions available. They did not give me part #s but he talked to parts while I was there to confirm they were available.I did not need it cable made on mine.
It looks like harness is adding a 2nd camera/TPMS to bed and keeping 1 in bumper. If you want to just move to bed of truck and don't need 1 in bumper the connectors are Molenx MX150 12 pin and about 3 ft of wire. I have verified connectors but haven't tested yet truck will be here next week.
Tow vehicles.Would it be possible to get a knowledgeable person from the major manufactures to explain their product answer questions ect.?Also Law enforcement or DOT to explain rules and regulation in regard to towing.
From your drawing it looks like you have 2000w inverter/charger and are planning on entire AC load being from inverter and are running both circuits thru inverter. Does inverter have built in transfer for AC? Can 2000w carry all your ac load? I have a 2000w inveter/charger with built in AC...
On pin box there is a junction box that has your 7 wire plug coming from.Inside the control wire for truck brake controller will connect to trailer brake wire,should be blue.You can disconnect there or if you can locate wire in trailer cut and use to operate actuator.
Wanted easier access to gray tank valve.I cut all the way across plastic behind sewer pipe.I used a piece of uni-strut across trailer frame above edge of frame. I attached a piece of plastic divider used between lattice panels to uni-strut. After trimming plastic underbelly was able to slide it...
The 80a I have seen are different.They are manual reset and switchable.There is a red button you can push to open breaker.They are what Lippert installed when they worked on mine.
On your wire harness extension.Ford has extensions for trailer harness.Could one those be made to work?When talking to a Ford rep he said getting plug into
bed was something they were looking at.Be interested to see how you make out with extension I will soon be in same position. Have you run...
Went to Homestead race this past weekend.Talked to a "Product Specialist" for Super Duty asked about TPMS and Camera.His answer for TPMS was they should work with aluminum wheels and steel belted tires only valve stem hole size could be an issue.He also said they will only tell you tire...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.