Page 2 of 2 FirstFirst 1 2
Results 11 to 12 of 12

Thread: A home made change that makes a lot of sense!!!

  1. Print this Post   #11
    Member
    Join Date
    Aug 2017
    Location
    USA - GA
    Posts
    43

    Re: A home made change that makes a lot of sense!!!

    Quote Originally Posted by BrannonB View Post
    That looks GREAT!!!! I have been wanting to do this as well, but my carpentry skills are below par so I haven’t tackled it yet. But that looks good.
    No big deal. Step by step, it's easy. My apologies for the rather lengthy reply.

    Step 1: Remove everything from the dinette, including cushions, seat OSB and anything else you find in the way.
    Step 2: Using a hammer and a piece of wood small enough to fit the plywood insert. Knock out the insert. and either remove the staples that remain, or hammer them flush. If you do not have an insert like I did, then a hole will need to be cut. Be sure to cover the wood with painters tape to avoid inevitable scratches while cutting the opening. Be sure to keep the opening roughly 2 1/4 in. from the floor.
    Step 3: Measure the opening. Mine measured 9 inches high, 17 1/4 inches wide and 44 inches deep.
    Step 4: Cut 16 pieces of 1x4 to the depth of your dinette bench. Cut them so they lay flat on the floor. I did not find it necessary to remove the carpet, but to each his own.
    Step 5: Screw and glue two 1x4 s together into a 90 degree angle. One for each side of the bench seat. so four total for this step. Set aside to let the glue dry, 1 hour should be plenty of time.
    Step 6: Lay your joined angled pieces on the floor and place 2 - 1x4s on top of each one. The upright angled piece should line up with the edge of thee opening, creating a guide rail for the drawer.
    Step 7: I chose 3 inch glue coated deck screws for this step, if you removed the carpet you might get 2-3/4 inch screws . The 3 inch length fastened the boards down and did not cause any issues with my slide. Drive one screw in the front middle of the top 1x4 driving it through all 3 boards. If you use a light weight wood like pine predrilling should not be necessary. If you choose to use a hardwood for the top rail then you may need to predrill to prevent splitting. One screw in the front, keeping the upright rail lined up with the edges of the opening and one screw in the back. The thickness of the 3 boards will stop and need for a center screw. Be sure all screw heads are sunk just below the surface.
    Repeat Step 7 until you have rails and guides on both sides of both openings.

    So far, no special skill required. That part will all be hidden anyway, right!

    Step 8: Measure distance between rails inside the opening. Mine was 17 1/4 inches. So I made my drawers 17 inches wide.
    Step 9: Measure the depth of the opening. Mine was 44 inches, so I made my drawers 40 inches deep.
    Step 10: Cut 1x6 lumber to size. Cut the side pieces to length. Mine was 40 inches.
    Step 11: Cut 1x6 lumber to size MINUS 1-1/2 inches. This will allow the sides to fit inside the side 1x6s. This is the best easy drawer construction, without special corner joints. I personally used locking dado joints.
    Step 12: Glue and screw the sides (40 in) and the ends(15 1/2) into a rudimentary box shape. Check square as necessary. This is best done by measuring diagonals from corner to corner and racking the box until both measurements are equal. Set aside to let the glue dry. 1 hour should be plenty.
    Step 13: Obtain 1/4 plywood for the bottoms. You can have it cut to size at your local Home Depot or Lowes or you can cut it your self.
    Step 14: Nail the bottoms to the premade boxes. I used 5/8 in. coated staples and an air stapler.
    Step 15: Test fit the drawers.
    Step 16: Measure the distance inside the rails you screwed to the floor nearest the opening. Mine was a bit over 12 inches.
    Step 17: Cut a piece of any left over lumber at least 1/2 think. Left over 1x4 works great for this. Glue and screw/nail it centered to the bottom of the drawer about 1 inch in from the end. This will act as a stop to keep the drawer from sliding out while travelling.

    Now the hardest part.

    Step 18: Obtain 3/4 plywood to cover the openings. I made mine 2 inches taller and 2 inches wider than the opening in the dinette benches.
    Step 19: TRY to get Heartland to sell you ONE yard of the fabric your cushions are covered in. I had no luck with this step, so I improvised. I Took one of the covers off a small cushion and went to JoAnn Fabrics and matched it as closely as possible. If you are uncomfortable with upholstery, I am sure there are local shops available that will handle it material and all for a small fee.
    Step 20: Attach drawer fronts to drawer boxes. I used 8 coated 1 1/4 deck screws for this. I drilled six holes about 1/4 deep on the ends and the middle of the drawer box front. Then 2 through holes that made an X pattern or the pattern of a five on a set of dice. These holes were just a bit smaller than the diameter of the screws being used.
    Step 21: Space upholstered drawer front centered against the front to the drawer box, using another piece if whatever was used for the stop blocks to make the boxes somewhat level. This will also give you roughly 3/4 in below the opening for the upholstered front. Which is just about perfect, IMHO. Start with the two through holes and attach the upholstered front with 8 screw total. Overkill maybe, but the front will not come off accidently.


    That's it, your done and you have the pride of saying 'I did it myself'
    Regards.

    Rich, Nikki(woof) and Du`Mass Pissant(meow)

  2. Print this Post   #12
    Member
    Join Date
    Dec 2017
    Location
    USA - GA
    Posts
    41

    Re: A home made change that makes a lot of sense!!!

    Thanks for the very detailed write up. That gives me more reason to do it, now I have all instructions. I have done a couple mods to mine, but hurried through it and didnít match the stain perfectly and have never went back and corrected it. But thatís just my lack of patience in wanting to get a job done. I will be trying this soon. Maybe even this weekend.

    Here is a link to my thread about my mods.

    https://heartlandowners.org/showthre...eer-DS310-mods

    Brannon and Megan
    2018 Pioneer DS310
    2006 F-250 6.0L

Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. it makes sense
    By MTPockets in forum Around the Campfire
    Replies: 1
    Last Post: 11-22-2016, 09:45 AM
  2. home made canopy
    By Mpg-al in forum MPG - Modifications
    Replies: 11
    Last Post: 12-08-2015, 08:02 AM
  3. The Mallard has made it home!
    By callowaykid in forum Where are you now? What are your plans? Any Heartland sightings?
    Replies: 5
    Last Post: 07-13-2015, 08:08 AM
  4. Made The Change
    By JWalker in forum Towing Rigs
    Replies: 17
    Last Post: 10-30-2010, 07:58 PM
  5. Home made air bag leveler.
    By ChopperBill in forum Camping Products
    Replies: 45
    Last Post: 03-13-2008, 01:59 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •