Recent content by Cutlers

I write this not out of anger or frustration but simply put, enough is enough. In Feb of this year we took a trip to Puerto Penasco MX. The trip was great, the Razor was great and we had a wonderful time. After getting home and cleaning out the TH, I noticed that on the DS rear wheel the...

Wife and I took our daughter to the airport in Vegas yesterday. We were southbound on I15 from St. George Utah to Vegas. I15 nortbound was packed with rigs leaving the Las Vegas Motor Speedway after the Cup race Sunday. We saw at least 5 Cyclones, 2 Razors and 1 Big Horn. I15 was packed with...

Nice looking unit! I'm curious about the pic showing the back view with the ramp down. It looks like some sort of bracket or assist bar at the lower right of the ramp. I'm trying to see if my ramp just needs more use to limber up some. After being closed, opening it and then unloading the...

It's Johnnie Walkers RV in Vegas. Not sure if he drinks Jack Daniels.....None

You could do what I did....Autometer digital EGT and boost gauges in a pillar mount....no need for more juice.....:-)

I don't know if this will help or not. I have an 09 3110DS. My 06 Rhino goes in just fine. I tie down by using 4" wide 10,000 lb ratchet straps one on each side. I put the straps front to back using the roll bar where in mounts behind the seats. I ratchet one side forward and the other backward...

I have one. Dealer provided it to seal the deal on my toyhauler. It's easy to use and easy to haul around. I put it on the roof by the ladder and use a bicycle chain/lock to secure it. Been in heavy rain and works fine. Since we're usually outside with the toys, one satellite is good enough. I...

Another stupid question...during my PDI, the tech and I found a blue coiled water hose with a quick connector in the basement. He said that it was the hose that connected to the outside spray ports. We looked and could not find any ports to connect the hose to. My question is did the 09 3110 DS...

I haven't learned about where that piece came from yet Big G...I emailed Jim B. and he has forwarded it to the factory, haven't heard anything yet. My fear is that if is a structural piece what problems am I going to have down the road. I hope that the factory has a plausible explanation...

Since dealing with our front jack issues, I believe that Heartland could make some improvements that would assist us and their dealers in making front jack repairs. The single most common problem with this type jack in all models is the bolt/shear pin issue. To facilitate this repair why not...

ummm...sorry to sound ignorant, but what measure does a can of tequila equal? I usually put my Patron in a shot glass so I'm lost here...on second thought those shots may be why I'm lost....:-)

Had a tech from our local RV dealer(not a Heartland dealer) come out and diagnose the unit. He said that the jack leg gears and jack itself were bent and the jack would not move and that caused the shear pin to break and the gears to strip. I called Heartland and they then handed me off to...

Today I took the flashlight and opened up the doors to the gen and propane compartments to look at the connecting shaft and motor. The connecting shaft has both bolts in it. The motor however, is loose and wobbles. Looking at the shaft while running the gear shows that the driveshaft is turning...

Hello, I hooked and unhooked my rig today and noticed that the off door side seemed lower that the door side. I finished unhooking and ran the front jacks up and down to see if they were working properly. The off side door jack is not going up or down, only the door side moves. looked at several...

In my 08 Chev with the IBC and the 3110DS I run mine at 7.5. I like mine stiff so if I need it it's there. We live in a rural area and not much stop and go stuff to deal with. The only time I lowered it was driving through Lake Havasu City. I lowered it to 6 to keep the stiff stops to a minimum...