Search results

Thanks for all the input, its a big job, and I want it done right the first time. It took CW almost a year to get my decal replaced under warranty with multiple trips back because they didn't order the right one, or forgot one or whatever. Not impressed and that was a job that I would think...

I need to find a place to repair my rubber roof near Sacramento, and not camping world in Roseville due to a bad warranty experience. Any help would be great, I don't mind traveling a little bit for good work. Thanks, jake

I'm in the same boat, they said turn the pressure shutoff down, not sure how many times I can turn it but now its leaking so looks like I need to call and get the upgraded one?

Re: Electirc Rear Jack Problem Bill, Yes that is the plan but if I can fix it I would like to do that. I just moved to your area, who do you recommend for warranty work? I took it in for some small stuff and after a month of them having it they hadn't even contacted heartland. I called...

Re: Electirc Rear Jack Problem Just experienced this with my 3010 yesterday, didn't have time to tear into it but will this week. its less than a year old and I'm not happy about it!!!

They sent me the whole assembly, just had to take a few measurements to make sure I got the right one.

This is an old thread but I just did mine on my 2011 3010 and dexter was great to deal with, they even offered to pay me to do it as if I took it somewhere. since I do live on an island in Alaska we don't exactly have a dealer near. Great customer service, and it only took 30 mins to do.

Thanks Porthole, here are the wheels on my Cyclone (8 spoke). I will look into what the actual psi rating is for the wheels, or if anyone knows off hand that would be great too.

Been looking at the G614's also, but just curious what the wheels on my 2011 3010 cyclone are rated for?

Porthole- Thanks will take a look, do you know if there is any breaker or fuse on the transfer box? I'm hoping it was a freak thing just from being so cold. I started it 2 weeks ago and had no problems at all. Also where can I find a good wiring diagram for my 3010? I tried in the wiki, but no...

Wingfoot- The breakers never actually tripped, but I turned them off then back on. At no time was there a load on the Gen Set. Normally when I start it, I watch for the TV light to come on and microwave to beep, kinda my tell tell sign the AC power is now on, and then allow it to warm up a...

porthole- Yes checked those, and reset multiple times. I am not using shore power, I was trying to run my Genset to power my heat gun to remove a decal, but after I started it, it never kicked on the AC power. I will be getting back in there tomorrow or Sunday and look around some more. Jake

JohnDar- Thats what I was thinking just not sure where to find it. I looked around but didn't have my batt drill to take off the wall in the basement, so that will be a job for tomorrow. Branson4020- I did not see any breakers, the 4x4 I think you talking about when i opened it up was just a...

I went out to run the generator today, started just fine. Waited a few minutes like normal for the AC power to kick on, and nothing. Checked all the breakers and fuses, in the trailer and at the Generator, ran it for almost 20 mins with nothing. Is there something I'm missing? It is 8* outside...

Riddler6.7, I just sold my 07 sb, I had no issues with out the slider pulling my 3010. The new 11.5 I will be recieveing this week will have the companion in it, and it is also a sb w/o a slider. Hope that

We do a whole lot of dry camping and don't like to run the genny if not needed. In my last TH we had two six volt batteries and could go 3 or 4 days. With this one we camped one night and in the morning the genny didn't have enough juice to start. We didn't run much of anything all day, and at...

Thanks for the info I will take a look today when i go get it for the weekend. I have not really maxed it out but I've been in some tight spots, I just keep a real good eye on it. Maybe today I will try it out though? I wish I would have gotten a Megacab, but I love my QC/SB. I have the Pac...

Elkstalker, I will take a look at the duct, would still like to know about the heat loss though. I have a Valley 16K Power Pull, non slider. As far as the truck it has the 5.9 with a auto. Riverman, the duct on the other side of the sliding glass door blows nice and hot so not sure that its a...

I have the same question about the garage duct not blowing hot air??

Just a follow up, still haven't recieved my 3010 yet but did decide what to do with the bbq. I ordered a Coleman road trip grill, its gonna work better for our situation. No need to drill holes in the side of my new TH and no need for a extra table to set the grill on. It has a collapsable base...

It is good to hear that Roseville has a good service department, since we will be transferring there next year, we will not have to travel far if we are in need of warranty work.

Thanks for the info, I really like that grill, I have seen it on Amazon. I will wait to get the trailer here and then figure out if it has the fitting or not. They told me it did, but when I asked where it was located, the sales guy said "I'm not sure, I will check," and he has not gotten back...

Still have not recieved my new 3010 yet, but am looking for a bbq for it. Where is the LP quick connect, what does the fitting look like (Picture?), and what bbq is anyone running? My last TH had one that attached to the side of the trailer (RV que), I can go that way or a stand alone on a...

Thanks Porthole, I just read the owners manual on line. It says 1 hour at 1/2 rated load and another 1 hour at 3/4 rated load. Thanks again, hope it gets here soon. Jake

Someone was telling me about loading it up with a load of 50% for an hour and half, with full load intervals. Has anyone done this or could it have just been my buddies generator instructions?

I will be getting my new 3010 next weekend and was curious if there is a break-in period for the 5500 Onan? I have heard some do, but does anyone know if mine will and what it is? I'm sure it will say in the owners manual but just trying to get ahead of the game. Thanks, Jake

I ordered mine in Late January, it will be done March 17th, and they are delivering it to Alaska by the 27th. They told me the process is 6 weeks but it really only takes 5 days to build it. As far as drivers, they had no problem with mine.

Thanks for all the input, I have decided to use the dealers shipper. I checked a few private contractors and they were within a couple hundred dollars, so might as well use a known good source. Thanks again, it will be here the 28th of March, can't wait!!!!

Our new 3010 is about to roll off the end of the line, and origanily I was going to drive down to Ohio and pick it up. Well I can not take that much leave at this time and was wondering if anyone has ever had their 5th wheel shipped? Also, it would have to be someone that ships to Alaska, just...

These are the awnsers I have been looking for, not that the other info is not good info. But I really wanted to here from people that actually use a non slide hitch with a short box and have no trouble. As I live on an Island and just going down to a hitch supplier and picking one up is not an...

It is piece of mind to have it, the thing is I already have a valley 16K, that does not have the slider. I have watched a few youtube videos where the sales rep states this 88* turn radius makes it so short boxes do not need a slider. I am just curious if anyone is doing it without a slider...

Hello eveyone, just purchased a 2011 3010 and was curios about the new 88* nose. I heard you do not need to use a slider with a short box, although I know it is recommended. What are you guys using with short boxes, I have a 2007 Dodge Ram QC SB. Anything would be great. Jake

Thank you guys for the warm welcome, I am hoping this will be the place for me to learn alot about my RV and how others operate theirs to make it a great experience..

New to the forum and a 5th wheel, but not to towing and rving. Just ordered my new 2011 Cyclone 3010, can't wait to get it and start using it. Hope to learn a lot from everyone here and maybe help some people out too. bggrndodge