Search results

Man, now that is what I call service. I am going to go right out there and get-er-done. I saw that little plastic clip, but was kind of afraid to mess with it, for fear of breaking it, then I would have had another problem. So again, thanks a lot for your help. Richard of Idaho #1686

While on my last trip, after arriving home, I found that the pocket door near the kitchen of my 2009 3400RL Big Horn was off of track on the rear (inside the wall) roller. I can't seem to get it back on the track, does anyone have any ideas as to how I can get it fixed? We had some pretty...

I think that is what I will have to do too, put it in the truck. My only concern is that I have one of those tool boxs in the bed, but I think that I can fit it in between the hitch and the box in the center. The generator stands about two inches proud of the bed so I can't put it on the side...

I have used a small ramp with an indentation on the top for a tire to sit in. I just pull up the good tire onto it, and it lifts the bad one off the ground enough to replace the tire. I don't trust jacks. I have had to do this twice, and it works great. Richard of Idaho

Thanks a lot guys for the input. I see that I have a lot to think about. Thanks again. R o I

Maybe you could try using a stud finder that you use to find the studs with in the house. Won't work on a metal roof though. Just a suggestion. Richard of Idaho

I have a Honda 3000is generator. I want to install into the front of my BH 3400RL. It is prewired for a generator. I did notice that there is a galvanized junciton box labeled as a "Safe guard generator overcurrent protector". Does the generator hook to this box. I do have the controls...

I found that those 90 deg fittings put some strain on the fitting going into the rig. I use those quick disconnect fitting from Home Depot. They stay attached, and all you to is stick the male part of it in, no turning required, and very fast. Just a thought. Richard of Idaho

Thanks Ray, appreciate it. I guess that I will have to check out how to run a cable too.

Antenna switch location Being a little over 5-6, I had a heck of a time trying to find that switch for my TV antenna/cable. I found it in the back of the TV. There is no room to get you hand in to switch the antennas. I have to use a stick to push that little button. Is there any way to...

Hey, thanks a lot Jim, I went out and located it ok. Richard

Living in the NW and having to clear my water lines in the winter, I just know that someday I will not get all the water out of the water pump. I have a 2009 3400RL Big Horn, and would like to have someone tell me where the water pump is located, and difficulty in getting to it. Thanks

ultra lube axles I think that I have Ultra Lube axles on my 2009, 3400 Big Horn. Just what does that mean? Do I still have to have them lubed regularly, or is it already done for me? Richard of Idaho

I have a Big Horn, 3400, 2009. My question is, are the axles on this the never lube kind, or do I have to have the bearings packed. Thanks Richard of Idaho

Man.....thanks a lot...that does not sound so bad. I have heard that you had to unplug the motor (wherever that is located) and I could not find anyone at the dealership that actually knew where it was. I like your idea better. I am sure that she will be able to hold on .....at least till I...

I have an electric awning on my 3400 BH. It works ok now, but what happens if I have it extended and it won't come back in? Does anyone know how I would be able to retract it without power? Thanks

I suggest that you move the amplifyer switch in the bedroom of the 3400 BH to a more accessable place. Being on the short side, it took me over an hour to find it initially. When I did, I could not reach it, and when I did, I had to use a stick to move that little switch button. Thanks...

The drain valve is located right in the middle between the two wheels, making it necessary to crawl underneath to open it. I suggest you move it either forward or aft of the wheels, for us old folks. Richard of Idaho

Man, am I glad to hear that. I knew he was wrong, but had to make sure. He is one of those guys who knows everything,....he thinks. thanks everyone for the info. Your right, we really love our 2009 3400 Big Horn. Had a HR Presidential before, can't compare to this one.

I was discussing my new Big Horn with a friend. He asked who made it, I told him Heartland. He said that they had been bought out by Keystone. Is there any truth to this statement. I sure hope not. Richard of Idaho

Can anyone tell me how much hydrolic fluid is supposed to be in the tank for the slide outs? Mine was half full at purchase, and is leaking by one of the cap nuts. I appears no one knows how much fluid goes into the tank, full or half full. Please let me know at indypen@earthlink.net. I...

I just purchased a new 09 Big Horn, beautiful rig too, I might add. I have had fivers in the past. I have a problem with this one, as I cant locate the drain valve for the fresh water tank. Does anyone know where it is located? I have a 3400RL, Big Horn. Thanks. You can contact me direct...