Search results

The Augusta was the same basic layout as the BH3670. The pipes for the W/D ran through a pipe chase above the curbside cargo door. At the port in the closet is where the shutoff valves were installed. If you can reach them, turn them off and disconnect the washer lines and attach a length of...

On the topic of closing off furnace vents. If you replace the stock floor registers with adjustable ones, there is no way closing off some to redirect the flow will result in damage or fire. Did it with the 3670 we had for almost 11 years. That’s not the same as blocking the lines right at the...

Back when we had a 3670 and s GMC 3500 dually, I put Timbrens on. Easy install, no fiddling with air lines, and without the trailer on, the standard leaf springs still rode “like a truck[emoji23]”. But then, we only towed twice a year, 200 miles to a seasonal site and back. Ya pays yer money...

When we had the 3670, I taped wire mesh over the grame holes then used spray expansion foam over it to hold it. For openings with wires or struts, a piece of old inner tube with a slot to a hole just big enough to fit over the object, screwed to the frame. Sent from my iPhone using Tapatalk

On the HL 5th wheels, it’s normally in the UDC, the small door behind the cargo door on the street side. Sent from my iPhone using Tapatalk

If it’s not in the UDC, look for a round opening in the frame on the sewer connection side. They’ve been known to hide valves behind the frame. Sent from my iPhone using Tapatalk

If the screen frame isn’t broken, you can replace the screen mesh yourself. Using a small flat blade screwdriver, remove the spline from the channel. It may be glued in spots, but you can work it loose by picking at it. Then remove the mesh. Use new mesh cut about an inch larger than the frame...

Plug your umbilical cord back into the tow vehicle and try it again with the engine running. Sent from my iPhone using Tapatalk

If you are able to replace it, find a brass one. The Sharkbite idea is a good one. When ours in the 3670 blew, it was behind the toilet, not the shower faucet. Remedy was to grab the lines to it and pull it down into the basement. Cut the junk off and used a Sharkbite one way check valve as a...

Undoubtedly the anti-siphon valve has self-destructed up in a wall cavity. If you’re lucky, it’s located behind a removable plate in the shower. Unlucky, it’s hidden in a wall cavity behind and above the toilet with no direct access. From personal experience, it’s a poorly designed piece of...

Back in the day, someone said it was basically an automotive electric window motor. Sent from my iPhone using Tapatalk

If feces left behind is a concern, maybe one of those dryer vent brush sets you connect to an electric drill would get it loose. They typically will extend(sections) to about 15 feet. Just be sure to always run the drill in the drive setting, not reverse, even when backing it out. If you reverse...

If you have one of the earlier versions of the Anderson valve, it may be leaking water to the tank even though it’s set to City water. Was a common problem a few years back. Sent from my iPhone using Tapatalk

Lifting with only one jack risks twisting the frame. Not a good thing. Sent from my iPhone using Tapatalk

The effluent from the gray kitchen tank can smell just as bad as a black tank if its left too long. Organics decompose and generate hydrogen sulfide, just like poop.[emoji1785] Sent from my iPhone using Tapatalk

Temporary toilets. They make a seat that you fit over a 5gallon bucket with a plastic bag liner for hunting. When we had a pontoon, I kept a small porta-potty on board for the wife to use so we didn’t have to run to every shoreside facility. Sent from my iPhone using Tapatalk

When we had our 3670, I moved it and the surge suppressor to the side of the bedroom step frame based on others postings about flooded electrical from that PoC anti-siphon valve. When it failed, the devices were high and dry, so I only had to mop up and run a dehumidifier for a while to dry...

Use the higher blocks on the rear tires then shim under the front ones with boards until they are snug under the tires. You could use a long level to find how much you need front to back to make the slope “level.” In essence, you’re making a long wedge to incorporate both axles. Sent from my...

Look into Two Factor log in verification for your financial websites. They send you a code via text or email (I prefer text to my cell phone) AFTER you’ve entered your ID and password. Sent from my iPhone using Tapatalk

Search repairing a tear in vinyl tile. There is a YouTube video that fits your problem with minimal effort. Sent from my iPhone using Tapatalk

You can buy an inexpensive handheld gas detector device on Amazon to check the gas fittings for leaks rather than slopping soapy water on them. The one I used when we had a rig is what found the not fully tightened furnace fitting following dealer service on it. We, too, would get a wiff of...

The only reason I put water in the fresh tank was to flush the toilet during power outages in the campground. The city water from the CG well was good quality made better via my filter system. Sent from my iPhone using Tapatalk

When we had our 3670, the OEM detector above the steps would go off when we used the toaster. Removed it and installed better units on the bedroom and living room ceilings. Added a CO detector under the island. Sent from my iPhone using Tapatalk

I can’t address the oven, but as for the smoke detector, what’s the manufactured date and when did you last change the battery? Unless it’s one of the more recent models with a built in LiH battery, they need to be changed at least annually. Unless the oven fire generated a fair amount of...

Is there a Studor valve under the vanity sink? Could be stuck open and when the water from the shower stirs up the tank, you’re getting odor coming out of it. On another note, sometimes a “musty” odor indicates wet wood somewhere. Check your drain and water lines for leaks, too. Sent from my...

If you haven’t already, remove the element and see if it’s caked with mineral deposits. If it is, you can soak it up to the threads in white vinegar to clean it off. And check at its terminals for continuity. I think there is an instruction in the Tools section for checking the thermostats...

The gas detector is normally wired direct to a 12V source so it’s always active. Because it activates does not stop it from working again once they’ve been cleared with fresh air. You can actually test them with the gas (no flame) from a butane lighter. Check the manufactured date on the back...

Good chance the 12V fuse panel is inside a cabinet somewhere (there has to be one). As for the motor, on past units it was simply an automotive electric window motor. No relay, just direct drive with the switch reversing the current flow for direction. Motor is at one end of the roller tube...

Maybe it’s the pricing of different brands. Been to a few RV shows and once you get past the “lipstick”, they’re still pretty much the same animal under the skin. Sent from my iPhone using Tapatalk

Two possibilities: 1) the drawer box is not square, or 2) one of the drawer slides is not mounted/aligned properly. Use a speed square inside the box to check all corners are 90 degrees. And compare the slide positions on both sides of the drawer and the frame. They’re not exactly made by...

To cut the Hanex countertop, a jigsw with a fine tooth blade should work. Your new sink should have a cut-out template with it. Secure that to the top of the existing countertop to properly cut the opening. If you're cutting more than just the radiused corners, drill a pilot hole for the saw...

In 2020, we “sold” our 2009 BH to the General RV we bought it from. Granted, it was 11 years old but in good shape, but their offer was a bit under what was still owed on it, so I had to make up the difference. RV Trader may list dealers that are looking for used RV’s. That’s how I found out...

Might be easier to remove what’s left of the chewed one and take it to a cabinet maker or lumber yard with a mill work shop and have them make you a new one. Sent from my iPhone using Tapatalk

If you can access it, replace it with a brass one. Sent from my iPhone using Tapatalk

Thing about vinyl, especially thin, flexible vinyl is that it loses it’s flexibility with age. Even becomes sticky. Sent from my iPhone using Tapatalk

If you research battery groups, you will find there are variations in the dimensions within a group. Yours is a Group 24 based on the sticker. It’s the cheapest battery for a dealer to install. The standard battery box on a RV will take a Group 27, maybe even a 31. Best to measure the box and...

If the motor runs and the connecting rod turns but the leg doesn’t move, it sounds like the shear pin is missing. A small screw and nut is a temporary fix. You said the rig is on the hitch and the gears look intact. Can you move the leg up manually and pin it? If the connecting rod isn’t...

On older hydraulic pumps, there was a 1/4” socket on the end of the pump motor that you could use an electric drill to operate the pump by inserting a bit into it. Might need an extension to reach it. Sent from my iPhone using Tapatalk

Having previously owned a 2009 BH3670, I can attest to the fact that the converter is probably up against the rear basement wall, above the black tank, in a pile of construction debris. That doesn’t do the cooling fan any good. Find it, move it out from under the black tank anti-siphon valve (in...

The clip installation was hit or miss even with the 2009 BH we had. Same issue with it starting to fall out after about a year. DIY repaired it myself. Sent from my iPhone using Tapatalk