Search results

hey there folks. I'm back with another project on the camper. Need to replace the bathroom floor due to a grey water overflow. How does the shower wall surround come off? looks like pop rivets holding it. also how does the vanity come out? really didn't see any screws when I did a quick...

back again. David-Steph, Dahillbilly, I don't use gas to heat water heater, just shore power. Only use the gas for the main heat and cooking. as far as the water heater, about 12 hours after I made my post and checking wires, I turned on the hot water facet and guess what. I had hot water...

Hi all. Just got back from camping and my Atwood water heater failed during the trip. Did some troubleshooting. Here is what's happening. Tank is full, turn on both heater switches. Sit outside and a couple of minutes later i hear clicking sounds, 5 or 6 clicks from heater. open panel and...

thank you all for the input on the greases. will have to get some lithium grease for the camper bearings.

I see a lot of owners praise lithium grease. what is wrong with the regular old wheel bearing grease i have used for years on my vehicles? I use a Moly EP type grease

I have a wilderness with ez lube fittings on it. my question is if i have only taken 1 trip of about 2200 miles, in 2 years, do i need to go ahead and hand pack or am i good with just shooting my hubs with grease for another trip? also, how do you remove the bearings with an ez grease sert...

I only paid 12,000 for my camper, used. can't see putting that much into refinishing my roof when i can do it for less than 500.00. Also, does anyone know if WD 40 will harm the EPDM coating? I found that WD 40 will remove the Dicor lap sealant really easy.

had the plastic cover off today and was looking at it. not quite sure about how i am going to seal it. maybe slap some under it with a brush, but looks like there is some sort of a foam gasket around the bottom.

after doing some research, I have decided to go with the Henry's Tropi-Cool 887. Going to use it on my seams, let it cure for 24 hours, then do the whole roof. I can't afford that Flex Armor. Feedback on this plan of action will be appreciated. thanks everyone.

I was reading the reviews, looks pretty good and is available at my local Home Depot. can i use the 885 seam sealer along all the seams, then apply the 887 coating? as of right now i don't have any leaks, but just want to be sure by using the sealer. thanks.

David, i tried to unscrew the lens. it was a no go. couldn't unscrew any of the lens on any of the other lights either.

here is a followup for my awning light. i finally found the fuse. it was located on the outside under the forward support arm trim. light now works great. thank you all for the input.

Hi all. My wilderness camper roof is looking rough and cracked. i want to go ahead and reseal it. was looking at Roof Magic because it seemed easy to use without a lot of prep work. I was also going to seal all seams with Eternabond tape. wondering what is the best or what have you all...

have 2 of these lights on my 2015 wilderness camper that don't work. one is over the bed and the other is over the dining table. there are 2 of these lights over each area with only one working in each area. how do you remove these lights and are they repairable? thanks.

I too need to replace the bath room door on my Wilderness. door taken off was 78 inches high. the area the door goes in is 82.5 inches high. bought a door at Home Depot that is 80 inches tall. was there a reason the original door was so short? or can i go ahead and mount my 80 inch door...

Thank you for the replies Bogie and Danemayer . Here is the picture of the jumper wire on the switches. The switches are mounted on the upper cabinet, so I am guessing the wiring is running down the wall.

been almost 2 months. no one has an idea? any long shots?? any ideas?? any tech reps follow this forum? please help. almost time for my vacation and i would really like to have my awning lights.:confused:

good evening folks. i have a wilderness camper with an LED light strip in the awning. light wasn't working and looked bad. replaced strip and it still doesn't work. checked for power at connection. no power. took switch off the wall, which is a double switch by the way. the other switch...

I had the slide out this past week. only thing I saw was steel cables on the top and bottom and nothing really supporting it. I do have some aircraft cable lube I can use on the cables. but that is really the only mechanical thing I saw.

hello Danemayer. bought this unit used and the owner couldn't find his owners manual. so really don' know what type of slide system I have on this unit. I saw there were a couple of different types in the folder. I just want to make sure I use the right cleaners and lubes

thanks for all the input. next big question is where to find a maintenance manual for the Wilderness 2175RB. i did see the generic owner manuals, but nothing for the maintenance. stuff like recommended greases for the slide, bearing grease, etc. anyplace to find this?

hey there NP_Chief, thanks for the reply. is that set up easy to install or should i get a dealer to do it. by the way, i am an aviation mechanic by trade, if that helps.

Hello all. new wilderness 2175RB owner here. what kind of equipment will i need to get that is usually required to tow this camper? we will be towing from Texas to Iowa at least once a year. i own a 2015 tundra crew max with towing package. any recommendations? thanks in advance.