Search results

Thanks, It appears that water is somehow getting into the molding (from the top??) and then following the molding until it can get out (where there is no caulk on the bottom). All the slides appear to be made the same, with no caulk on the top, so just can't seem to figure why this one is...

Here are a couple of areas to look. The check valve may be faulty---I have replaced mine about 3 times before I found one that is not faulty from the mfg. Also behind your docking station, where the check valve turns into your plumbing lines may have a loose connection--very easy fix. When you...

We are leaving from seattle the end of May. Which way do you go to tget to Dawson creek? Up 97 or did you go up Kaloops? al

Hi everyone, We continue to have a water leak on the left side (from inside) of the bed. I think??? I have narrowed it down??. Near the top of the slide there is a piece of molding, the roof material goes into this molding, but no calking on the top of the molding. There is caulk on the bottom...

Where are you headed in ME, we lived in that state for over 35 years where I practiced Forest Management. We can give you plenty of ideas about the northern/eastern part of the state, just let me know what specific areas you are interested. al

I have had to replace the plastic check valve several times before I got one that worked consistently. Not a hard job to replace, but just surprised so many were faulty, either the small spring or the spring hold down were usually bad. al

Thanks, Alan---the T & P valve you refer to--is that the pressure relief valve? al

Hi everyone, I am having an issue with my water pressure regulator (watts 263a). I have emailed the mfg and cleaning is the first option which did not work (the pressure rises over time). The next option Rich (rvwaterfilters) suggested is perhaps I have lost the air bubble in my water heater...

We workcamped at Wine Country RV park in Prosser. It was great. Large pull through sites, within walking distance of several wine tasting wineries. Heated pool and hot tub, grass sites, not much shade. We di do a revies on rv reviews al

Hi everyone. We live in the 3670 BH and time for yearly maintenance. I usually get the refer and the water heater done, however have been thinking about the furnance. It has been cold this past winter and the furnance ran almost every night without an issue. Do they need cleaned becasue they sit...

I agree with JohnDar, I also had water running down the wall of the slide and then pentrating into the exposed plywood. I contacted HL and they sent me plastic angles for all the slides and that took care of the problem. I would check your other slides to see if they are having the same issue. al

I have Michelins and they have performed every bit as they are advertised---I did have an alignment issue and had to move the fronts to the rear (dually), but the tires are doing great. al

I also attached mine from the stabilizer to the frame in the front of the stabilizers. I could not find anything strong enough in the rear of the coach, so drilled through the frame and put them pointing toward the front--they work just fine. al

I also have aluminum wheels and tighten cross wise, then torque to 120# using a torque wrench. al

I checked several of the post on this issue and just need some clarification. Ours is not leaking at the floor nor do we have water on the floor. It does not seal in the bowl. According to the threads, I should try to push down on the seal---shouldn't I be pushing up so it seals against the top...

I was also concerned aboput getting the compressor to do 110#. I found someone in the campgraound that had a husy from home depo. I tried it out and it worked just fine for my tires (110#). I purchased one for myself from home depo and have been very happy wih it. If I was to buy another I...

Another suggestion that may help. When we were in Prosser, WA last summer I purchased a small solar fan. I mounted the fan near the heat coil of the refer and put the cord out the vent and the solar collector just sitting on top of the slide--it helped us quite a bit to keep the refer cold. al

Great suggestions/advice--let me try a few and see how I make out---If I need to take the weight off the axle, will I need to do that each time I grease or do you think there is some dirt in there and should be ok once I get that removed? I had not thought about the fitting being bad--that will...

Hi everyone, We had wet bolts installed on our 2010 BH 3670 at the same time we had our CP installed. They greased the wet bolts during installation? I now can only get grease into a few of them. If I remember correctly?? the bolts have a samll hole in them and that hole needs to be installed...

As other have said you should have no issues pulling/stopping with your current set up. One suggestion I would make is to load your trailer for your typical travel gear and go to a scale. Take weights for your truck axles (front/rear) and your trailer axles (front and rear). YOu should be able...