Search results

I use the level up to repack wheel bearings as well. I lift it up with level up and use jack stands while still attached to truck. This way I can rotate tires too. Sent from my iPhone using Tapatalk

Yes, thank you. I am aware of that. Will probably do that on generator power otherwise I may forget to do it next time we hook up at RV park. Sent from my iPhone using Tapatalk

That crystal and silver look similar to what we use. Sent from my iPad using Tapatalk

Ordered two EasyStarts on Wednesday before thanksgiving, 11/25/20, shipped the same day and got them today, 12/1/20. Now find time to install. Been wanting to do this for at least two years. Sent from my iPad using Tapatalk

When I had mine IS done in September 2018, I already had the 7k disc brakes from Performance Trailer Brakes installed. I had MorRyde install their 8k IS on my trailer. They were able to take my 7k disc brakes and install them on 8k IS. I think by changing the caliper mounting plate. The 8k...

I have a 2016 Bighorn that had a kitchen/laundry grey tank leak. I determined the grey tank material was HDPE.

1/2” sharkbite is what you need as everyone said. But, since you asked, PEX OD is 5/8”. Sent from my iPad using Tapatalk

Thanks you veterans! Ours is a great country because of you. Sent from my iPad using Tapatalk

I used these. https://amsolar.com/rv-mounting-accessories/91m-35ms Didn’t bother looking for trusses, just screwed into roof. Then put enough Decor self leveling caulk to completely cover screws and brackets. After 5 years and one trip to Alaska, no movement or leaks. My panels were 100...

Here’s a picture of the heating pad on one of my grey water tanks. Sent from my iPad using Tapatalk

I too am wondering the same thing. I couldn’t find any reference to a cap in the installation or parts manual. I have been concerned about the heat from the burner that is vented into the back of the refrigerator cabinet and how to get it out of there Sent from my iPad using Tapatalk

This sound just like WD-40 with the addition of the waxy film for lubricate. Sent from my iPad using Tapatalk

If.....you’re ceiling vent is open when you flush and your black tank vent terminates close to bathroom ceiling vent. Then, as air is expelled up black tank vent, it can be sucked back into the bathroom through the ceiling vent. Sent from my iPad using Tapatalk

Very good job at making something work then. The way you did that is exactly the way I’ve done it many times on home plumbing. When pipes could not be removed. Sent from my iPad using Tapatalk

Just curious. If you cut that double elbow off trailer. Why did you go to the trouble of removing old pipe in stead of just getting all new parts? Sent from my iPad using Tapatalk

This: https://www.zoro.com/mueller-industries-90-deg-double-elbow-3-inhub-03047/i/G1247775/feature-product?utm_source=google&utm_medium=surfaces&utm_campaign=shopping%20feed&utm_content=free%20google%20shopping%20clicks&gclid=EAIaIQobChMIjpeli4GC7AIVLB-tBh3wqwjyEAQYAiABEgLBsfD_BwE Plus this...

This is what I used as well Sent from my iPad using Tapatalk

That’s funny. Sent from my iPad using Tapatalk

If you have a ohm meter it’s easy to check element condition before you remove it. Sent from my iPad using Tapatalk

The toilet flange is, absolutely, glued to the ABS pipe leading to the black tank. The flange is then screwed to the floor. This keeps the toilet from moving when it is attached to the flange via toilet bolts. The best was to replace the flange is cut the pipe, if it is accessible, behind...

This is also where I got mine. When I added some vent openings. They were even able to tell me what color was installed in my Bighorn. Sent from my iPad using Tapatalk

To answer your original question. The new Anderson valves are not cheap knockoffs and you cannot disassemble and regrease them. They are a sealed brass ball type valve with multiple ports. If it’s happened more than once to you, I’d replace with the new Anderson valve. This assuming it’s not...

Ok. That’s a good question. It was about 5 years ago I removed it. I’ve removed so many of them over the years (I was a plumbing contractor) and I cant remember where it was on the BH faucet. Thought I think it was in the inlet to the spray head. Sent from my iPad using Tapatalk

Dan is right. Check valve is the problem. You could, also, stick a small screw driver in the main water connection and push, back and forth, the check valve (it’s spring loaded) and hopefully knock some debris loose to let it close. Sent from my iPad using Tapatalk

I too draw a lot when using slides or level up. I draw closer to 60 amps though. I installed an 80 amp manual reset breaker and #4 wire from battery to pump. I think that’s the only permeant fix. 50 amps doesn’t work very good on 60 amps of draw. I elected a manual reset breaker because...

Every kitchen faucet with a pull out hose has a check valve installed (it’s code). Sometimes they’re in the spray head (where hose connects), sometimes where the spray hose connects under the faucet body (up under kitchen sink). Removing the check valve can solve a lot of low flow problems. I...

I still like the logo before the current one. The one with the farm silhouette. Like in the heartland of America. Sent from my iPad using Tapatalk

I used this one and it helped. I now have snap pads and that helps more. I haven’t use fluid additive. Sent from my iPad using Tapatalk

Get a top quality residential toilet seat by Kohler or Toto. Not cheap but you won’t have to come back here and ask which toilet seat to buy. Don’t think you’ll find a better RV toilet than the 320. Sent from my iPad using Tapatalk

If I’m more than one bubble out of level I won’t open them. Slides are a little bit of a balancing act. Best to be as level as possible. IMHO. Sent from my iPad using Tapatalk

https://www.amazon.com/gp/product/B004RCXD0G/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 Sent from my iPad using Tapatalk

The cover was put on upside down. The GFCI breaker has been tripped. Turn it all the way to off, then turn it back on. If it trips again you have a ground fault some where. Sent from my iPad using Tapatalk

Every suggestion Dave made is absolutely correct. Sent from my iPhone using Tapatalk

Is that the same place as Island Park, ID? There is a nice RV park in Island Park as well. Sent from my iPhone using Tapatalk

Has anyone used this. https://www.etrailer.com/Tools/Curt/C51701.html Seem like an interesting gizmo and I like techie stuff.

This what I used. https://www.amazon.com/gp/product/B0031Y7Z0A/ref=ppx_yo_dt_b_asin_title_o02_s03?ie=UTF8&psc=1 Ours was painted. Obviously, it shouldn’t be painted. After our trip to Alaska last year a lot of the paint had chipped off so I just replaced with black. One of the easiest...

I completed my repair on my galley/laundry grey tank. I had a small crack as seen in the picture below. I determined the tank material is HDPE (High Density Polyethylene) and confirmed by BigFry’s research that came up with Alpha tanks. https://www.alphallc.us/tanks/page/2/?filter=on I...

Put these in a couple of months ago. https://www.crutchfield.com/p_107DB522/Polk-Audio-DB-522.html They sound a whole lot better than the original Jensens, but not as good as my little rechargeable Bose I got at Costco. Sent from my iPad using Tapatalk

https://www.amazon.com/AP-Products-018-341-Black-Premium/dp/B007EXPANS...

I have the same problem on my galley tank. In the exact same place, it sounds like. I’m going to repair it using these: https://www.amazon.com/gp/product/B00VMGO1K6/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1 Haven’t done it yet but will in the next two weeks. I’ll use my heat gun set...