Search results

Wow that pic didn't show up very good. I'll try again Sent from my SM-A515U using Tapatalk

If you have the CRE 3000 (that's what I have) I went to their spec chart and torqued mine at 40 ft. Lbs. Sent from my SM-A515U using Tapatalk

I have the CRE 3000 with disk barkes. Sent from my SM-A515U using Tapatalk

Thanks, I'll check them. Sent from my SM-A515U using Tapatalk

Mine are dry. I believe I'll change mine to wet one's when I get back. Leaving Sunday to go to North Ga. to do a little trout fishing.🙂

I decided to get my tires balanced and lifted camper to get tires off ground (manual overide) and heard a loud pop (Like metal snaping). I have heard this noise several times before and searched and searched unable to find the source. By lifting the camper, it was very obvious... One tire was...

Will Heartland have a rally at the fairgrounds in Goshen, Indiana this year (2021) ?

I have Coachnet. Mine has paid off ($100 deductible) and I am well ahead of the purchase price.

I've had 2 water valves go bad. I suggest drying the area real good and stuff a clean dry paper towel between bottom of foot pedal and base of toilet. Flush several times and see if paper towel is wet. If you happen to have a bad water valve DO NOT remove pedal. There will be 1 or 2 screws in...

Danemayer, I got kinda excited there for awhile. I did a little research on the 3 yr structure warranty. I found out the unit had to be built after November 1, 2017. Mine was built March 16, 2017 and I didn't purchase until January of 2018. Mabe they will feel sorry for me and make an...

Your opinion's please... First of all, I am not bashing Heartland, Im just try to share some of my experience's that my fellow owner's may avoid or check theirself. Should a 2018 Landmark Oshkosh (the long slide of slide in slide) floor be rotted out in 2 yrs 8 months, which is used mabe a...

Are KIB controlers Bluetooth compatable and if so what year did they start?

Can someone, anyone please help me. I need a professional schwintec tec. I am so frustrated with my 2018 Landmark Oshkosh that I'm ready to sell it. The long slide, with the slide in slide has quit for about the 9th time. I am so tired of holding my breath, wondering if it is going to come in or...

Where did you get the rollers and how did you get the screws out? I have 2 screws on front roller that back out and use a pair of pliers to screw them back down as low as I can get them.

I had the inverter replaced the 1st year I had my camper.The GFCI outlet on the inverter would trip. Through all the testing it was determined my inverter was bad. I replaced it and things were good for a while. Then I noticed it cutting off again. I just completed about a 300mi trip and the...

I have a Landmark Oshkosh. The long slide of the slide in slide has had the motor replaced what will be 4 times. The #1 motor at the front of camper. I just replaced the motor the first of January 2020. I have let the slide in and out mabe 4 times.I have been in 1 park for about 3 months. I let...

Sorry y'all, I left of a 0. It $1000 Would you still do it?

Need some advice... I have found a 2007 5500 Marquise Gold generator for $100. It runs good and has voltage on both legs. I don't plan on using off the grid but just if ac is off. 1. Would you invest in this? 2. Would 5500 run my rv? (2018 Landmark Oshkosh) 3. Would you just invest in a portable...

What kind of problems have you had ? I have an 2018 Oshkosh also.

I can't trust mine. I replaced (warrenty) my first inverter because the GFCI breaker would trip everytime when disconnecting from shore power and traveling. Now that it has been replaced it still will trip when i disconnect from shore power and traveling just not as often. (No one seems to know...

Carl, yes they were fine. Actually they were good and snug. It just didn't take a whole lot of effort to loosen them. Once I got them loose I just took a hammer and a couple of taps and the leaf springd lined right back up. ( Matter of fact, I could not tap on the leaf spring to get it line up...

Marc, thanks a million! You were right , out of the 4 leaf springs 2 leaf spring bolts were loose! Problem fixed, thanks again!

Thanks, I'll check mine.

I was installing Glowsteps to my RV today and noticed the leaf springs were out line. Seems the rebound clip is missing. I also noticed the one across from it is loose and about to fall off. Just wanted to bring this to everyone's attention so you can be sure to check yours. Thanks, Jerry

I agree Lou, after taking a closer look I believe it was being repaired also. I guess I had imagined this in my mind before. Then I find this picture and thought, I've always wondered about this. You watch the slide (schwintek) go out and as it meets the wall it gets kinda tight and motor...

I saw this on another rv site. (SOB) It's a Swintech slide. How can this happen? Kinda got me concerned after I saw it.

I'll check inside tomorrow, thanks.

Anyone have an idea what can cause these scratches under slideout above roller? Thanks in advance.

Does anyone know where I can get a replacement light? I have google it and can't seem to find any with the part #. TIA!

Needing information on an Insignia refrigerator model # NS-RFD21SS7. My refrigerator stopped making ice.The ice maker is turned on. Any suggestions will be very much appreciated.

Looks great ! What size and where did you purchase it? I like that idea for a trager.

What is your tire preference when replacing your tires on your truck (TV)? Have any of you gone taller or wider on your tires? Thanks!

I use the Harbor Freight electric hoist also. The next one above the $99 one. I lower hitch to a 4 wheel dolly and roll to where ever I want. You will be surprised at the other uses you can use it for. Real handy to lift lawnmower to change blades also.

I have been told (by a friend)not to connect my Champion generator to my Landmark. He said it would damage the electronics in the rv. He said I needed to get a Honda because Champion is not pure sine wave. Is this so?

Great job! Looks awesome! Sent from my SM-G900V using Tapatalk

Dan, I think what you're seeing is the reflection of my camera on my phone. It's seems the surface is real smooth and the cracking pattern is underneath, if that makes sense. Sent from my SM-G900V using Tapatalk

I was cleaning and waxing my front end cap today and found this (see pic's). Is this a problem? Is it the paint or is the end cap cracking? Thanks in advance, Jerry Sent from my SM-G900V using Tapatalk

Congratulations! Sent from my SM-G900V using Tapatalk

If you can enlarge this pic, look at the heads of the screws. Over tightening Sent from my SM-G900V using Tapatalk

I haven't taken it apart in case the factory wants to look at it. But to answer your question, it is higher than the others, looks as if it was cross threaded, also the porcelain under it is broken. Sent from my SM-G900V using Tapatalk