Project LM 365
- Thread starter Jesstruckn/Jesstalkn
- Start date
-
- Tags
- locks
Jesstruckn/Jesstalkn
Well-known member
Dave
Both sides of have a plastic insert to cap off the front and I have that same piece on both sides of my entry steps. look under yours at the entry step and see if you have that insert. Maybe you could get it from Heartland.
Sent from my XT1254 using Tapatalk
Both sides of have a plastic insert to cap off the front and I have that same piece on both sides of my entry steps. look under yours at the entry step and see if you have that insert. Maybe you could get it from Heartland.
Sent from my XT1254 using Tapatalk
Last edited:
Jesstruckn/Jesstalkn
Well-known member
Lady DonnaUpdate on the GE Advantium Profile..... THE WIFE LOVES IT.
This one is a winner for sure. The cost is kinda crazy but it seems to be working better then we had even hoped for. We have a bit of a learning curve but all going well.
Rhond's Pizzookies came out perfect last night, and the Rum cake cooked a bit faster then it does in the oven at home. Finally a success..
Highly recommend the GE Advantiume Profile despite the high cost
here's your picture of the racks. 
Sent from my XT1254 using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
Update on the "Buzzing" Transfer switch replacement. Well after all of the back and forth with Heartland I had received the right transfer switch. The (TRC Surge Guard) after installing the new switch back in in the exact same way as the old one, flipped on the 50amp breaker and waited for everything to come on........ Click Click Click the new switch was Buzzing too I noticed when I was loosening the jam screws the 3 on the right (the ones the factory used) had drops of lock-tight on them and the 3 on the left did not. So I mover the feed wires over to the left side and tried that. Much much better. Still has a very slight buzzing but nothing like it was when connected the right side. I have no idea why this would be, it all should be the same.
I noticed when I was loosening the jam screws the 3 on the right (the ones the factory used) had drops of lock-tight on them and the 3 on the left did not. So I mover the feed wires over to the left side and tried that. Much much better. Still has a very slight buzzing but nothing like it was when connected the right side. I have no idea why this would be, it all should be the same.
Jesstruckn/Jesstalkn
Well-known member
Maybe
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
Update on the Wilson Eqo antanna ....
I have not talked to the right guy yet but I will try again tomorrow.
That guy I talked Friday told me it was wireless but after reading there website that doesn't appear to be the case.
I will keep working on it with Wilson and pass it on to all of you that are interested.
Sent from my XT1254 using Tapatalk
I have not talked to the right guy yet but I will try again tomorrow.
That guy I talked Friday told me it was wireless but after reading there website that doesn't appear to be the case.
I will keep working on it with Wilson and pass it on to all of you that are interested.
Sent from my XT1254 using Tapatalk
Last edited:
TravelTiger
Founding Texas-West Chapter Leaders-Retired
For20hunter
Pacific Region Directors-Retired
Thanks Jerrod!!
Eons ago when I used to go nuts with Christmas decorations I used a contactor to turn on the lights. It supplied 4 20 amp circuits. It always buzzed.
The unit has an electromagnet and that is what produces the buzz.
I really don't think you will eliminate the buzz.
And that's the daily buzz.
Peace
Dave
Jesstruckn/Jesstalkn
Well-known member
Right now with the way it's hooked up I no longer hear it from inside the RV. Way better than the old one
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
Dave I made an attempt to move this post....
Up date on the The GE Advantium profile microwave/convection oven.
VERY VERY HAPPY
With it...
This unit is the Mercedes-Benz of microwaves. Beings this is the only oven in the Landmark 365 we wanted the best we could get and finally after many attempts have found the right one.
Sent from my XT1254 using Tapatalk
Up date on the The GE Advantium profile microwave/convection oven.
VERY VERY HAPPY
With it...
This unit is the Mercedes-Benz of microwaves. Beings this is the only oven in the Landmark 365 we wanted the best we could get and finally after many attempts have found the right one.
Sent from my XT1254 using Tapatalk
Bones
Well-known member
Dave I made an attempt to move this post....
Up date on the The GE Advantium profile microwave/convection oven.
VERY VERY HAPPY
With it...
This unit is the Mercedes-Benz of microwaves. Beings this is the only oven in the Landmark 365 we wanted the best we could get and finally after many attempts have found the right one.
Sent from my XT1254 using Tapatalk
Ha Funny. We will have to see if it works..
Jesstruckn/Jesstalkn
Well-known member
Small easy Mod
I installed a motion sensor on the light in the entry coat closet. I plan on adding to it and putting 1 more light down under the bottom shelf to light up the floor area.
Sent from my XT1254 using Tapatalk
I installed a motion sensor on the light in the entry coat closet. I plan on adding to it and putting 1 more light down under the bottom shelf to light up the floor area.
Sent from my XT1254 using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
Check out these baby's
42"
500 pound capacity locking in and out
Full extension rollers.
They are for my next big project of a large pull out drawer under the coach for the satellite dish and the gas fire pit and anything else I can fit in it.
Sent from my XT1254 using Tapatalk
42"
500 pound capacity locking in and out
Full extension rollers.
They are for my next big project of a large pull out drawer under the coach for the satellite dish and the gas fire pit and anything else I can fit in it.
Sent from my XT1254 using Tapatalk
