Project LM 365
- Thread starter Jesstruckn/Jesstalkn
- Start date
-
- Tags
- locks
Jesstruckn/Jesstalkn
Well-known member
FYI the frame is 24" front and 24" rear and all the SnapPads are at 9.5"
Jesstruckn/Jesstalkn
Well-known member
Oh ya I'll have to do that Steve thanks
Sent from my XT1585 using Tapatalk
Sent from my XT1585 using Tapatalk
Bones
Well-known member
It still says GMC. Ha
Jesstruckn/Jesstalkn
Well-known member
I have bigger problems right now.
We had to cancel our final 2016 6 day trip to the coast to deal with a major sewer line problem at the rental house.
Sent from my XT1585 using Tapatalk
We had to cancel our final 2016 6 day trip to the coast to deal with a major sewer line problem at the rental house.
Sent from my XT1585 using Tapatalk
TikiDawg
Well-known member
**** auto correct.
Well that's a "crappy" situation.
Sent from my SM-G900V using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
Rhonda fixed the signature page for me yesterday. Should be good for a few years now.
Sent from my XT1585 using Tapatalk
Sent from my XT1585 using Tapatalk
Bones
Well-known member
Jesstruckn/Jesstalkn
Well-known member
You have no idea !!!!
That is actually how we make our money. By trucking treated poop around North California.
I have been dealing with TREATED sludge for 20 years now. And still don't like dealing with the fresh stuff.
Sent from my XT1585 using Tapatalk
That is actually how we make our money. By trucking treated poop around North California.
I have been dealing with TREATED sludge for 20 years now. And still don't like dealing with the fresh stuff.
Sent from my XT1585 using Tapatalk
jimtoo
Moderator
jassson007
Founding Louisiana Chapter Leaders-Retired
#1 in the #2 business
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Jesstruckn/Jesstalkn
Well-known member
I have picked up the custom box from powder coating today and will install it soon. I'm still working on a solution to extend the harness without cutting it. However my other major problem has been talking up most of my time.
Sent from my XT1585 using Tapatalk
Sent from my XT1585 using Tapatalk
CarterKraft
Well-known member
I have picked up the custom box from powder coating today and will install it soon. I'm still working on a solution to extend the harness without cutting it. However my other major problem has been talking up most of my time.
Sent from my XT1585 using Tapatalk
I haven't come up with anything but I have found some possibilities. I would really need to have the harness connector to identify it. Can you get any numbers off the harness side? Often the connections on the plugs, sensors etc. are not made by the plug manufacturer they are just replicated by the outfit making the hardware. Identifying them is difficult because they aren't made to be identified.
Jesstruckn/Jesstalkn
Well-known member
BBQ Lift system 2.0...
Found some extra time this morning so I installed the 6" lift actuator. I had to cut off the lower mount and weld on a new one about 4" lower. The I used a rattle can of hammered black paint to touch it up.
I didn't want to have to re powder coat it.
Now it will go lower, fold up smaller, and lift higher.
Sent from my XT1585 using Tapatalk
Found some extra time this morning so I installed the 6" lift actuator. I had to cut off the lower mount and weld on a new one about 4" lower. The I used a rattle can of hammered black paint to touch it up.
I didn't want to have to re powder coat it.
Now it will go lower, fold up smaller, and lift higher.
Sent from my XT1585 using Tapatalk