Search results

Pole one on the Hughes Protector is tripping. I've narrowed it down to the front AC. I've pulled the cover and the compressor capacitor looks fine. However, the fan capacitor has one burnt wire. I don't have a meter to check each one. I'm hoping the compressor itself isn't fried. 1- Could it be...

Does anyone have any suggestions to get the electric schematics for my 2028 Bighorn 3870. I need a full diagram, and also assume the charger is located in the rear underbelly. As it’s not in the garage. My mechanic came down and test all electronics, and I’d requesting the schematics. Thanks David

Yes sir, your analysis was correct. The tank has dropped off it’s angle iron supports on both sides and has dropped 3-4”. Even worse is one side is bowed in substantially. I have found a reliable on site RV tech, I honestly think I’ll be purchasing a new tank. However, he did discuss how...

This is the leak between the valve and the tank. I’m not certain how their connected. The hose strap is tight. Sooo, what and/or how is it connected that could cause this leak? Thanks so much: David

Hi, I have an intermittent leak under the front underbelly, indicated by an occasional drip coming from the front underbelly. I had to make a small cut in the underbelly in order to let the water drain out. (Not a lot, enough!!) I let the black tank get full ( pressure??) and did laundry today...

Thank you sir, I’m looking at it and have no clue how to access it in order to clean it.

“Then electronic circuitry”

Thank you everyone!! First I do have pet’s, so cleaning will be the first step. The electronics. Best wishes!!

My electric fireplace will only blow heat for a few minutes the the heat shuts off. This is regardless of the settings. Any input would be helpful!! Regards, David

It’s gotten cold here in St Louis, however, the temperature has warmed up enough to thaw the drain pipes. Originally, the black tank valve was frozen, and would not budge. Since it’s warmed up constantly for a few day’s, the valve opens freely. However, it’s not draining. I have tank heaters...

How do I adjust my Sundance awning so water doesn’t pool up? Thanks for your input. David

My Furrion oven won’t stay lit after multiple attempts. Seems every time I light it and close the oven door the flame goes out. Thanks, David

I recently was in a flash flood. Water entered in the lower front of my rig, dropped the under belly, fortunately no damage. So to my point: If I wanted to override the leveling stabilizer, and lift the rig front and back to their highest point. (I.e) lifting the rig off the ground; how do I...

Thank you!

Yes sir, thank you. Currently, I’m utilizing heat tape and have the Anderson wrapped. It got below zero here and has/ will remain cold, so it’s no surprise. I will utilize a light to heat the manifold and pipes on the inside connections. I’m assuming you plugged into the outlet in the garage...

My Solution To Frozen Plumbing After Trying Everything On My 3870FB The UDS opening/access is sealed with proper insulation. The H20 connection in the UDS is heated in insulated with pipe insulation. The Camco heated hose is flowing. There are no “low point drains “. I made sure the furnace ran...

Re: Froze up: Where are the low point drains on a 3870 Solution!!! Yes the UDC opening is sealed. I had to pull the panel inside the crossway storage, or garage, and pull the panel to gain access to the plumbing. I used a hair dryer to thaw the manifold and put heat tape around the pipes and...

Re: Froze up: Where are the low point drains on a 3870 I’m certain my H2O supply is fine. I’ll double check. No water to any faucet.

It’s 0° outside and I’m froze up. My Spicket and water hose supply are both heated and functioning. I am heating the water control compartment, as well as running the furnace. I’ve read that the low point drains can also be the culprit. However, embarrassing to say, after owning many rigs, I...

Thank you.

The information given is right on the spot. I’ve made it through temperatures below zero degrees following the aforementioned advice. Once again: turn off the water supply to the refrigerator and drain that system. I always put insulation behind the refrigerator through the outside access...

Thank you! - - - Updated - - - Thank you!

I have found one anti siphon valve behind the shower. Where I the heck is the other? I’ve looked everywhere!! Thank you

I have found one anti siphon behind the shower. Where may the other be located?? Thank you

Thank you all for your replies and attached diagrams. I’ll be taking the wall down and tracing the lines.

One in the same!!

I have two black tanks that drain out of a single discharge. In the water control cabinet there are two unmarked flush connections. When I connect to one there is no flow. When connected to the other it shoots the water out of the other flush connection. I tried a Y connection, still nothing...

Good morning, this rig has two black tanks. In addition, inside the compartment there are two black tank flush connections. When I hook the hose up to one connection it appears to be flowing appropriately. However, when I connect to the other water shoots out of the unconnected inlet. I’ve...

Thank you: Should I go with a "Shark Bite" or equivalent?

This connection is in need of replacement: what diameter water supply line is it, and what size parts and procedure is required to do so? I realize it has the crimping connection and was going to replace with a hose clamp. Is there a way to remove the crimp with out the correct removal tool...

Thank you for your help. Heartland is addressing the claim. David

There were several warranty issues submitted to Heartland for blatant constructional issues. They refuse to authorize reimbursement for repairs done by a Certified Master Technician. We all spent a substantial amount of money for these rigs, only to find out there is no support from the...

Sabre Red makes a gel spray now. 20' stream, has me curious. My opinion, is it is a great deterrent, and if it's not a situation where lethal defense is required. I'm to old to fight! Thank you for your service!!

Thanks for your reponse guy's. I had already jumped on it and had done as you directed. Problem: The center roof of the slide-out bows down. The bladder seal on top had an approx. 6 inch run where it was not secure firmly to the slide-out roof. Temporary fix: Ran a bead of silicone to temp seal...