Search results

15mins for 425*

Never used before how long does it take to pre-heat?

Hey BigFry. These video's are great, why don't they make them in the real world when one is in an RV park maybe? See my pictures I found that the rear end is fixed when I think there should be a pivot (that is where mine was leaking at the stud) because something has to give when that slide goes...

Anyone had there window leaking I see dripping of the frame at the top quite a bit, any tips where to look could it be caulking at the top frame outside?I thought it was the EXIT window but apparently not. Whats next with this tub?

Today Thursday I spoke to Sigma Switches and suggested something like a butter knife to push down on the location lugs.

Has anyone have real good way of removing these switches out of the panel without damaging the surface. I thought that the four clips would push down but don't, suggest a tool. I have a couple that have failed. Den.

Mine was a leak in a crack in the weld at the fixed end of the cylinder.

IMO. When you have your coach looked at get them to check the tracking looked at, on my old coach after the second blow out I had a hanger re welded to put the axle in line,could be trying to turn the corner down the road, just a thought. Den.

A mobile tech was in the park today and took him 15 minuets to reinstall the window. Den.

Something else have you checked your hangers from the king pin? mine are our out. I see on another RV forum that this guy welded the hole and moved it back to get the wet bolt in the correct position. If there off.. I reckon the trailer is trying to turn a corner going down the road scuffing the...

A while ago I bought a Hunter fan from Home Depot bought a long down tube cut shorter to make sure the blades missed the slide outs when closed also that plastic cheapo ceiling rose dumped for one I made myself. This fan is a three speed with lights and does moved the air now the fan is lower...

Any joy with yours DougNZ? Do you know that I forgot that I had this access deck hole in my shop, it could save doping the belly and I have in the past replaced both the galley and bath gate valves on this tub, so I am now thinking when time arises I thought about cutting and make up a back up...

You could have the cut out hole slug in there when they drilled out hole for the down pipe and has floated to the gate valve shutting off black water. Been there done that. Good luck. Den.

They aren't cheap?

Hey do know what with reference to the rear cap no longer on there leaving the hospital this week Las Cruses on the the I-10 we came up on a GD and you know what my Bev call's the coaches withe flat back she say's they look like a loaf of bread withe topper off!!

Good morning. I found the invoice for you I will take a picture of the can when I can to the shop. That ceiling rose I made I found the maple ply sheet 4x4 not find the invoice for that thou. My bathroom trim is pealing shoddy, like to replace at some the trim later. I think I bought the Maple...

Do you know what I did, bought Maple wood on line and stained my new ceiling rose and had found the stain thorough Heartland I think it is Vintage Antique something? and I bought a quart.. mailed to me and matches all the other paneling in the house we thought it turned out well also I can cover...

Today's progress a better day thanks to all They pulled out one of the drainage tubes today from the lugs heart soon I am told,do you know that I would never known anything about it if had never visited a tooth surgeon for a extensive root canal. could have gone on my merry way and not known...

Thanks guys I hope to be out of here by Sunday. This hospital here in Las Crues NM treats me very well Tuesday was very tough. indeed I have go walking again today what we take for granted each day yes. Den.

Hi Dave. Yes triple plus a couple things in there as well, well i will say not much fun, god must have place for me.Den

t boy it is having mack truck driving through ones chest one have experiences? den.

Today I took the window out from under the tape and installed the seal around the frame, and now and after finding on line the sheet :- Lippert's WINDOWS QR-178 HEHR 6400 window it says there to install at 45 degrees but I have nurmous attempts no joy. So disappointed in my 365 investment.

Perhaps they will now fabricate there own frames/chassis and place them in a oven and stress relive all the weld and give Joe Blogs the inspection results on purchase.Yes? Not that I would ever buy another 5er after what I found over the past years. SAD. Den

Been a while, but we like the unit it is quiet cost less to run than the overhead units and also very quiet one could run her a night no problem with sleeping. We have been running her from late mornings to about 9:00ish depends, during the summer heat and has risen to the 110*+ at times here...

Dave. It is on its way, I went for the 7/16" x 3/16" for anyone else tackling this project at a cost of $82.14 inc shipping. Den.

Hi Dave thanks that's the plan this afternoon did send them a message earlier, no reply yet. Den.

Would you use 7/16" X 3/16" It looks like to me exiting seal is 3/8"x1/8" not finding anything like this out there, do you think the 3/16" would squash down for a better seal? I stuck in the window with tape until I make the decision in what order. I have not found any info or seals on the...

We just had thunderstorms and had a bad water leakage firstly I see that the window does not shut off around the bottom side corner looking out. I thought I would check out the seal flat foam. I thought it would have been rubber bulb shape? Any way like another post the window fell out. I could...

This brand new pump above in this thread gave us a F-05 code a few days ago, so I then stripped her down I see that the waste water migrates into the motor housing because of I think whatever the bearing is made of in the plate breaks up. I found like a thick sort of carbon looking material in...

As a toolmaker we all ways had a QC department which is "quality control" when in England and worked on parts they were checked and recorded.

My wife liked the idea of the top loader just like the old days but now after doing the research they say the new ones are not as good the old ones. The pocket where we would place it has enough room with a little work with moving the drain pipe snug against the wall and a gas line installed...

Good morning Dave. Will do, not done anything yet just doing the research at this time. Cheers Den.

I have been told Inverter goes to the gen side treating the inverter as a gen.

Hey Jess. Since I drew that up someone said to me that the Magnum should go into the gen side I guess there are different schools of thought on that. Den.

Was there a owner here on this forum that had a Bighorn and installed a all in one. Our Splendid washer is playing up again those boards are spendy. GE - 2.3 Cu. Ft. Top Load Washer and 4.4 Cu. Ft. Gas Dryer Laundry Center - White Model:GUD24GSSMWW

I lost Southwire 41261-50 last week funny that the shore 50 breaker was bad as well!!

I my old Everest the 50amp breaker was in the center of the panel so when adding say the magnum you could tot up the amps to it panel balanced yes? I bought double breaker for my mini split along with the Magnum and filled up the slot on the right end. Is there a need to balance the panel up or...

Dave. The problem got solved. I did a check the continuity between plug and three nuts LI,L2 no burning there in the reel then to ATS no leaks so coach is good so then the park management changed the breaker and no it seem to be fine. Cheers. Den.

That works for me. I have cover off after our meal I going to check stuff. Den.