Search results

Go to Lippert's website and down load their recommended procedure for repacking wheel bearings. After reading all of the previous post, which I agree with, little has been said about the proper way to force grease into and through a rolling element bearing. Lots of folks believe that just...

Duane - I agree that the Progressive hard wired unit is the way to go, had this on my last trailer. Bought the portable Progressive EMS units 30 and 50 amp off of Ebay at a very good price. I rewired the 30-50 amp cord yesterday and checked the rewire with Ohm meter as suggest by John B. I...

Re: No Heay low 20s Help Fred, Does the fan run when you set the T-stat to heat and adjust to sufficient temp to run the furnace? I know this is a basic question, but we need to start some where. I know that you have checked the propane supply, therefore we must assume that if the stove...

Matt, Thanks for sharing your experience with refer repairs. I don't know if the single Radio Shack 5" fan has sleeve or ball bearings. The tag on the fan said that is rate for 30,000 hours of operation. I have by-passed the thermal switch by adding a 'on/off' switch. Currently I am...

Laurent, Thought I would sent pictures of the 50 amp female plug that shows the wiring arrangement so that you can compare it to the wiring in your 50 amp plug. According to the 50 amp plug the wire location of the white and green wires are reversed. Having said that, I still is puzzling to me...

I have a 30 amp and a 50 amp Progressive portable EMS, both of which showed the RV post 30 and 50 amp plugs to be wired correctly at the parks post. As to the electrical consumption, when either the micro wave or the HW htr was in operation, neither in operation at the same time, the voltage...

I have a 30 amp cord that has a 50 amp female marine plug that is for some reason causing a GF once it is plugged into the RV. I have been using this extension cord for about a year without any problem. Just arrived in Florida RV park and when I plugged the cord into the RV is when I got the...

Jerry - glad to hear you folks are having good weather and a great time. We bought our CarryOut from Tweety's in San Antonio. At the moment I don't plan to use the ladder mount on concern for tree that might obscure the signal. Sounds like the folks that have the CarryOut mounted to a ladder...

Just purchased a new Wineguard Carryout Satellite Antenna at the recommendation of JayC at the Canton, TX rally. The question of how to secure the Antenna so that someone will not carry it away when we are not at RV has risen in our household. Any suggestions from those that use this type of...

As always, thanks for the valuable input. I am on my way to Lowes to buy some foam board! Prior to now, I had never given consideration for the foam board insulation and the fact it will not asorb water, which is a plus.

I have physically compaired the Lippert/Venture gear box with the Domar and the results.... same gearbox made at the same location. The only difference is the Venture gear box is more than twice the price of the Domar box. For future reference, buy the Domar gear box. Not only is their box...

I have removed the front section of coroplast to repair water damage from a leaking 1/4" ploy tubing to the refer icemaker. Since the coroplast and aluminized bubble rap is down, could or should I add some fiber glass insulation to the underbelly for added thermo value? The weight of 3 or 4...

Re: So far, so good I believe that the Heartland portion of the BH trailer is above average, but the Lippert frame construction, i.e., welding is some of the poorest quality that I have seen. I hope that Thor Industries will have some influence on Lippert to put more effort into quality of...

It can be done, but you will have to know location of the rafter so that the hole that penetrates the roof and ceiling is not in conflict with one of the rafters. You may also choose to box in the opening between the roof and ceiling such is done for A/C and roof mounted fans. Be sure to select...

I recently by-passed the thermo switch located on the condensing coil fins that controls the two small cooling fans so that the fans run continously when the refer is in operation. This was done bases on key learnings from reading many post, not only those on the HL forum. Much to my supprise...

As Ray suggested, I jacked the front of the trailer up very high with two large floor jack and cribbing. Back of trailer is almost touching the ground. Was able to remove the Door Side (D/S) leg without any problem. The O/D/S is going to be another story because the leg is exterior of the...

I have had a problem with the wiring insulation that goes to the magnet being cut by the sharp edges of the brake shoe which resulted in a direct ground. You might ask the brake controller folks if this would give the same fault code.

Does anyone out there know how to remove the landing gear legs on a 2010 BH model 3410RE. The landing gear (LG) legs are mounted external to the frame, i.e., between the front compartment enclosure and the exterior wall of the trailer. After removing the leg from its clamps (2) there is very...

If you are talking about heating the valve body, be very careful with the heat because you can easily destroy the TEFLON ball to body seating/sealing material.

Follow Jim's method of fix or slide the refrig out of the cabinet and install a new vinyl hose.