Search results

Cold water lines will expand when hot water starts running through it, and will have a ticking noise as it grows longer and slipping along the supports.

Reservations made

We have an 06 Landmark Mt. Rushmore, owned it since 09, we have had a few issues, but nothing to get overly excited aout. They all have their quirks, most are very minor, some are dealer issues, some may be major. All in all, you have a house that is a rolling earth quake every time it is...

Active volunteer firefighter, 21 years and still at it.

Toy Haulers by design, are pin heavy, to balance out when the garage is loaded.

Lifted truck, not enough truck, not enough hitch.

I would gain acces to the top of the tank if you can, on our Landmark, the vent pipe was broke off at the tank. It is a threaded fitting that sheared the threads off. I was able to cut the pipe and install a new end on it.

140 ftpd for 9/16" studs 120 ftpd for 1/2" studs

Make sure your rig is level, very important!

That style you can but just the flap, I had located one on the internet back when we bought our Landmark in 09.

I am a welder fabricator, the welds had little to no penitration. The tear in the frame is the only place they had decent penitration. If it had been welded correctly, the hange and/or the frame would be torn appart. Absolutely weld failure.

Bent axles, take to an alignment shop for over the raod trucks.

Cancle the sale! They need to be giving you a comparable vehicle to use. They can not hold your vehicle hostage if you owe no money against. Sontact the state's attorney general.

Possile wasp nest interfering with the fan on the condensor side.

The delay allows the generator to stabilize before applying a load.

When living in ours for 9 months, over the winter, I placed fibergass insulation across the bottom of the refridgerator inside the bottom vent. Stuffed it so air could still circulate through but closed it off around the water line and valve. We had temps in the single digits and still had the...

MorRyde has a better system than the ones shown in the video. I have this on our 06 Landmark since new, and works flawlessly, while adding 4" of vertical trave to the suspension. http://www.morryde.com/products/89-lre4000-re-suspension-system

Wasn't going to try and horn in on any activities they had planned for the number of attendees or anything else, just trying to get a feel of the attitude and the genuine nature of the people involved. I was not impressed, even when we walked right down the row of all the attendees and...

I appreciate all of the words of encouragement, I even had one chapter leader PM me, which was surprising. Even more surprising, it was one of his rallies we attended. I replied to him explaining it was one of his rallies and to which one. I bet he didn't expect that, I have had no response...

I glad to see everyone has enjoyed going to different rallies, our experience has been quite different. We were very excited to attend our first rally about 2 hours from us. When we arrived and setting up, we had another couple with us with a brand new North Trail and this was their first...

Remove the generator and do it right, this an area you do not want to take any short cuts or half-***** attempts to repair

Actually, it is one circuit. The main breaker is either undersized or weak.

Re: Dura 3-Hole With Pressure Issues? Remove the aerator and clean it.

No, red and black are always the hot legs, reversing them has no affect at all.

Something isn't right, your bolts should not be loosening up. I tow heavy, very heavy at times, I have never had any issues with the bolts or mountings coming loose. You bolt holes are oversized/egged out from being loose and will only get worse. You need to drill them out and back to round...

I use a Samsung Tab A in my RZR with the GPS Waypoints Navigator. Uses GPS satellites to navigate. I have never had it fail on the trail hear in the Ozark Mountains or the Boston Mountains. I downloaded the maps off of the internet, and map/navigate the trails I ride. 90% of the tails I have...

Better find out why they are coming loose. Usually there is some movement in the connection, or the bolts are to small for the hole driled. The hole can also be egged out from the movement. The bolts could be too short as well, threads in the hole. Bolts should be long enought to have all...

1/2" studs 120 ftpds 9/16" studs 140 ftpds

When we wintered in our Landmark a couple of years ago, I placed a section of fiberglass insulation around the bottom of the fridgevand tucked it in so air could still circulate through as to not hinder the operation of the fridge. Ran it on electric and had ice all winter long. Temps did fall...

Don't just run bleach through it, put a couple of tablespoons of bleach in it form to top cap and let sit over night, then flush it out

Installed a wireless back up camera, pics to come

Check your incoming power! Since the CG is having electrical issues, you may have/or not damaged some of the componants that run on 120 volts. I would find another park ASAP.

Check your tank, is it sagging out the bottom or falling out?? Ours was sagging severly and started to fall out on the curb side, the outlet was on the road side. I raised the tank and re-supported it. No more sagging.

Reverse polarity on batteries??

Look into upgrading to 17.5" wheels and tires. I did it for $5.00 more for the tire/wheel combo than replacing the 16" tires. Now I am good for 6,005 pounds per wheel and tire. Way over kill, but I do not expect any issues. I have been running 2 years and have been very impressed.

You need to have the input before the onboard regulator. If you use the quick connect as an input, you will have the 2 regulators fitting each other and will be releasing propane. The reason is, they will not have the same outlet presure, so the one with the lower presure will be releasing gas.

I replaced all 3 my self, I installed Barkley electric valves on both grays, replacing the cable operated ones. The black valve was a direct connect to the UDC with a rod extension, so I left manualy operated. Total cost of parts was just under $250, and about 4 hours of work in my drive way...

When we purchased our Landmark used, I noticed most of the plastic ends on the rungs were broken, I ordered the peices to replace all of them. When I removed the ladder to make the repair, I saw how flimsy it really is. The ladder is sitting in the loft of my shop and has been there for 8...

Ladders are not a mounting point for anything!! They are not designed to have any weight mounted to them and bounce it down the highway.

What is your axle capacity?? Fifth wheels are designed to carry 20-25% of gross weight on the pin.